夏日-双锥真空干燥机温度过高解决办法
发布时间：
2018-07-30
关键词：夏日-双锥真空干燥机温度过高解决办法
首先：确定干燥设备散热管有没有堵塞 ，导致热量无法散出，，会使得双锥真空干燥机的温度升高。还有尽量避免双锥真空干燥机被太阳直射，如果放在场内摆放，双锥真空干燥机应该避免前后两台靠着摆放，不通风。通风不好一系列问题都可以引发了干燥机温度过高。
First of all: to determine whether the drying equipment heat pipe is blocked, resulting in heat can not be dissipated, will make the double cone vacuum dryer temperature increased. As far as possible to avoid the double cone vacuum dryer by the sun directly, if put in the field, double cone vacuum dryer should avoid the two sets before and after placing, not ventilated. A series of problems caused by poor ventilation can cause the dryer temperature to be too high.
及时清理好发动机机身的油污和尘土，保证发动机保持良好的散热。
Clean up the oil and dirt of the engine fuselage in time to ensure that the engine keeps good heat dissipation.
应认真做好破碎机设备维护保养工作，定期对设备进行全面检查，做好设备维修保养，更换发动机“三滤”及机油，更换或调整皮带，检查风扇、水箱、发电机、压缩机等部件是否能正常运转。
The maintenance work of the crusher equipment should be conscientiously done. The equipment is regularly checked, the equipment is maintained, the engine "three filters" and the oil are replaced, and the belt is replaced or adjusted to check whether the parts of the fan, water tank, generator, compressor and other components can operate normally.
因为热胀冷缩原理，高温会使破碎机的零部件膨胀，导致各部件的咬合处产生更多的摩擦和偏差，不仅会影响生产进度，摩擦还会使温度进一步升高；
Because of the principle of heat expansion and contraction, high temperature will inflate the parts of the crusher, resulting in more friction and deviation at the biting place of each component, which will not only affect the production progress, but also increase the temperature.
检查冷却系统、燃油系统否通畅，并更换老化的电线、插头、油管、螺丝、紧固燃油管路，防止燃油泄漏。
Check the cooling system, fuel system is unobstructed, and replace aging wires, plugs, tubing, screws, fasten fuel pipelines to prevent fuel leakage.
为设备更换恰当的机油粘度等级，一般夏季机油粘度等级要比其他时候适当高一些。发动机机油及各处润滑油需更换使用夏季用油，油量合适，经常检查是否有漏油情况，特别是燃油，应及时补充。
For the equipment to replace the appropriate oil viscosity grade, the general viscosity level of summer oil is higher than that of other times. Engine oil and lubricating oil everywhere need to be replaced and used in summer. The amount of oil is suitable. Check whether there is oil leakage, especially fuel oil, should be added in time.
夏季高温，增加设备故障率以及火灾发生率，请您务必为每台机器随机配备1-2台灭火器，以防不测。
Summer high temperature, increase equipment failure rate and fire incidence, please be sure to each machine randomly equipped with 1-2 fire extinguishers, in case of accidents.
夏季室外温度高，高温容易对设备造成不良影响，建议您无论设备处于停机还是工作状态，都尽量保证设备放置在荫凉处，如夏季高温可为设备搭建临时遮阳棚，避免设备长时间在太阳下暴晒。设备日常保养为保持破碎机设备处于^好的工作状态，并且可以随时可以投入运行，减少故障停机时间，提高破碎机完好率、利用率，减少破碎机磨损，延长破碎机使用寿命，一定要做到定期保养，制定好合理的保养计划，正确处理使用保养和修理的关系，这一点千万不能大意。设备轴承保养破碎机轴承工作很重要，因为轴承部位是^容易坏掉的，在使用中磨损比较大，所以需要经常保养，经常加油才能增加轴承的使用寿命。设备润滑保养在破碎机日常工作中要注意和及时做好摩擦面的润滑工作，这样可保证设备的正常运转，并且有效延长破碎机使用时间。一般情况下加入轴承座内的润滑脂为容积的50-70%，每三个月必须更换一次，换油时应用清洁的汽油或煤油仔细地清洗轴承滚柱的跑道。
In summer, the outdoor temperature is high and the high temperature is easy to have bad effects on the equipment. It is suggested that the equipment should be placed in the shade, if the equipment is in a stop or working state. For example, a temporary sunshade can be built for the equipment in summer, so that the equipment can avoid exposure to the sun in the sun for a long time. The daily maintenance of the equipment is to keep the crusher equipment in the best working condition, and can be put into operation at any time, reduce the failure time, improve the integrity and utilization of the crusher, reduce the wear of the crusher and prolong the service life of the crusher. It is necessary to ensure regular maintenance and make a reasonable maintenance plan. It is very important not to deal with the relationship between maintenance and repair. Equipment bearing maintenance crusher bearing work is very important, because the bearing part is the most easy to break, in the use of more wear and tear, so it needs regular maintenance, often to increase the life of the bearing. In the daily work of the crusher, equipment lubrication should be paid attention to and timely lubrication of the friction surface, which can ensure the normal operation of the equipment and effectively prolong the use time of the crusher. In general, the grease in the bearing seat is added to the 50-70% of the volume, and must be replaced every three months. When the oil is changed, the runway of the bearing roller is carefully cleaned with clean gasoline or kerosene.
First of all: to determine whether the drying equipment heat pipe is blocked, resulting in heat can not be dissipated, will make the double cone vacuum dryer temperature increased. As far as possible to avoid the double cone vacuum dryer by the sun directly, if put in the field, double cone vacuum dryer should avoid the two sets before and after placing, not ventilated. A series of problems caused by poor ventilation can cause the dryer temperature to be too high.
及时清理好发动机机身的油污和尘土，保证发动机保持良好的散热。
Clean up the oil and dirt of the engine fuselage in time to ensure that the engine keeps good heat dissipation.
应认真做好破碎机设备维护保养工作，定期对设备进行全面检查，做好设备维修保养，更换发动机“三滤”及机油，更换或调整皮带，检查风扇、水箱、发电机、压缩机等部件是否能正常运转。
The maintenance work of the crusher equipment should be conscientiously done. The equipment is regularly checked, the equipment is maintained, the engine "three filters" and the oil are replaced, and the belt is replaced or adjusted to check whether the parts of the fan, water tank, generator, compressor and other components can operate normally.
因为热胀冷缩原理，高温会使破碎机的零部件膨胀，导致各部件的咬合处产生更多的摩擦和偏差，不仅会影响生产进度，摩擦还会使温度进一步升高；
Because of the principle of heat expansion and contraction, high temperature will inflate the parts of the crusher, resulting in more friction and deviation at the biting place of each component, which will not only affect the production progress, but also increase the temperature.
检查冷却系统、燃油系统否通畅，并更换老化的电线、插头、油管、螺丝、紧固燃油管路，防止燃油泄漏。
Check the cooling system, fuel system is unobstructed, and replace aging wires, plugs, tubing, screws, fasten fuel pipelines to prevent fuel leakage.
为设备更换恰当的机油粘度等级，一般夏季机油粘度等级要比其他时候适当高一些。发动机机油及各处润滑油需更换使用夏季用油，油量合适，经常检查是否有漏油情况，特别是燃油，应及时补充。
For the equipment to replace the appropriate oil viscosity grade, the general viscosity level of summer oil is higher than that of other times. Engine oil and lubricating oil everywhere need to be replaced and used in summer. The amount of oil is suitable. Check whether there is oil leakage, especially fuel oil, should be added in time.
夏季高温，增加设备故障率以及火灾发生率，请您务必为每台机器随机配备1-2台灭火器，以防不测。
Summer high temperature, increase equipment failure rate and fire incidence, please be sure to each machine randomly equipped with 1-2 fire extinguishers, in case of accidents.
夏季室外温度高，高温容易对设备造成不良影响，建议您无论设备处于停机还是工作状态，都尽量保证设备放置在荫凉处，如夏季高温可为设备搭建临时遮阳棚，避免设备长时间在太阳下暴晒。设备日常保养为保持破碎机设备处于^好的工作状态，并且可以随时可以投入运行，减少故障停机时间，提高破碎机完好率、利用率，减少破碎机磨损，延长破碎机使用寿命，一定要做到定期保养，制定好合理的保养计划，正确处理使用保养和修理的关系，这一点千万不能大意。设备轴承保养破碎机轴承工作很重要，因为轴承部位是^容易坏掉的，在使用中磨损比较大，所以需要经常保养，经常加油才能增加轴承的使用寿命。设备润滑保养在破碎机日常工作中要注意和及时做好摩擦面的润滑工作，这样可保证设备的正常运转，并且有效延长破碎机使用时间。一般情况下加入轴承座内的润滑脂为容积的50-70%，每三个月必须更换一次，换油时应用清洁的汽油或煤油仔细地清洗轴承滚柱的跑道。
In summer, the outdoor temperature is high and the high temperature is easy to have bad effects on the equipment. It is suggested that the equipment should be placed in the shade, if the equipment is in a stop or working state. For example, a temporary sunshade can be built for the equipment in summer, so that the equipment can avoid exposure to the sun in the sun for a long time. The daily maintenance of the equipment is to keep the crusher equipment in the best working condition, and can be put into operation at any time, reduce the failure time, improve the integrity and utilization of the crusher, reduce the wear of the crusher and prolong the service life of the crusher. It is necessary to ensure regular maintenance and make a reasonable maintenance plan. It is very important not to deal with the relationship between maintenance and repair. Equipment bearing maintenance crusher bearing work is very important, because the bearing part is the most easy to break, in the use of more wear and tear, so it needs regular maintenance, often to increase the life of the bearing. In the daily work of the crusher, equipment lubrication should be paid attention to and timely lubrication of the friction surface, which can ensure the normal operation of the equipment and effectively prolong the use time of the crusher. In general, the grease in the bearing seat is added to the 50-70% of the volume, and must be replaced every three months. When the oil is changed, the runway of the bearing roller is carefully cleaned with clean gasoline or kerosene.
上一条：双锥真空干燥机中^核心部件解析
下一条：各类粉体混合机粉体均化评测
